See The Examples For More Information

Aus Kössler Lehrerlexikon
Zur Navigation springen Zur Suche springen


SISF-based mostly device tracking could be enabled manually (by utilizing machine-monitoring commands), or iTagPro support programmatically (which is the case when offering device monitoring providers to other features). SISF-Based gadget monitoring is disabled by default. You'll be able to enable it by defining a system tracking policy and iTagPro support attaching the coverage to a particular target. The target could possibly be an interface or a VLAN. Option 1: Apply the default machine tracking policy to a target. Enter the gadget-monitoring command in the interface configuration mode or in the VLAN configuration mode. The system then attaches the default policy it to the interface or VLAN. Note The default coverage is a constructed-in coverage with default settings; you can't change any of the attributes of the default policy. In order to have the ability to configure device monitoring coverage attributes you must create a customized policy. See Option 2: Create a custom coverage with custom settings. Option 2: Create a custom coverage with custom settings. Enter the gadget-monitoring coverage command in global configuration mode and enter a custom coverage title.



The coverage that is created, and best bluetooth tracker its settings, are system-outlined. Configurable coverage attributes can be found in the machine monitoring configuration mode (config-device-tracking) and differ from one launch to another. When you attempt to switch an attribute that's not configurable, the configuration change is rejected and an error message is displayed. For launch-particular details about programmatically created policies, see Programmatically Enabling SISF-Based Device Tracking in Cisco IOS XE in the required version of the doc. Starting with Cisco IOS XE Denali 16.1.1, the present IPv6 snooping and iTagPro product IP Device Tracking (IPDT) commands have corresponding SISF-based gadget-tracking commands that enable you to apply your configuration to each IPv4 and IPv6 handle households. After you may have upgraded from a Cisco IOS XE 3.x.x release to a Cisco IOS XE 16.x.x release, enter the machine-monitoring improve-cli to transform legacy IPDT and pet gps alternative IPv6 Snooping commands to SISF-based system monitoring commands. After you run the command, only the new machine-tracking commands can be found on your device and the legacy commands should not supported.



Based on the legacy configuration that exists in your device, the system-tracking improve-cli command upgrades your CLI in another way. Consider the following configuration eventualities and the corresponding migration outcomes before you migrate your present configuration. You can't configure a mixture of the previous IPDT and IPv6 snooping CLI with the brand new SISF-based mostly device-monitoring CLI. In case your machine has solely IPDT configuration, operating the machine-monitoring upgrade-cli command converts the configuration to use the brand new SISF coverage that is created and itagpro device connected to the interface. You'll be able to then replace this SISF policy. If you happen to continue to use the legacy commands, this restricts you to operate in a legacy mode the place only the legacy IPDT and IPv6 snooping commands are available on the system. On a machine with existing IPv6 snooping configuration, the previous IPv6 Snooping commands are available for further configuration. Use the system-monitoring upgrade-cli command to transform all of your legacy configuration to the new SISF-primarily based machine monitoring commands. After conversion, only the brand new device monitoring commands will work in your gadget.



Use the legacy IPv6 Snooping commands to your future configuration and do not run the gadget-tracking upgrade-cli command. With this option, solely the legacy IPv6 Snooping commands are available on your gadget, and you can't use the brand new SISF-primarily based system monitoring CLI commands. On a device that has each legacy IPDT configuration and IPv6 snooping configuration, you can convert legacy commands to the SISF-based mostly gadget tracking CLI commands. However, word that only one snooping policy will be connected to an interface, and the IPv6 snooping coverage parameters override the IPDT settings. If your device has no legacy IP Device Tracking or IPv6 Snooping configurations, you need to use solely the new SISF-primarily based device monitoring commands for all of your future configuration. The legacy IPDT commands and IPv6 snooping commands are not out there. Starting from Cisco IOS XE Denali 16.3.1, the ip dhcp snooping vlan vlan command creates a system tracking coverage programmatically, to help the IEEE 802.1X, web authentication, Cisco TrustSec and IPSG features.



The programmatically created policy tracks each IPv4 and iTagPro support IPv6 purchasers. Be sure that this command is configured, if you're using any of the aforementioned options. Table Table 1 displays legacy IPDT after which the IPv6 snooping commands they are transformed to - if the system-tracking upgrade-cli command (international configuration mode) will not be executed. Table Table 2 shows legacy IPDT after which the SISF-primarily based machine-tracking commands that the system converts them to, if in case you have executed the gadget-tracking upgrade-cli command. Set to the default value, and can't be modified. Set to the default worth, and cannot be changed1. Set to the default behavior, and cannot be modified. Set to the default worth, and cannot be changed. Set to the default worth, and cannot be changed3. Set to the default behaviour and can't be changed. Enters the worldwide configuration mode. Specifies the interface and enters the interface configuration mode. The gadget monitoring coverage shall be hooked up to the required interface.